How to Repot Calathea Ornata

You may want to repot your calathea ornate because of some reasons. However, you may be afraid that after you repot it, the plant can languish, or have a lot of brown, crispy, dying leaves. To avoid these bad things, you are able to repot your calathea ornata by following the instructions below.

The Things That You Need to Repot Calathea Ornata

According to the pro florist, here are several things that you need to repot calathea ornata.

  • You need a pot which is bigger than you used previously. You have to measure the diameter of the pot opening. Usually, the new pot should not be more than 1 to 2 inches larger than the previous pot.
  • You need a suitable potting mix. You should note that this plant needs a potting mix which can retain some moisture, but it can drain well. You are able to use a mix of 60% houseplant potting mix and 40% perlite.
  • You need a table or a flat area. Since repotting is a messy process, it is better if you use a surface that can be cleaned by wiping it. So, you can put some newspaper or you can use a potting tray so that the mess can be contained.
  • You need a small trowel or large spoon. If you want, you can just use your hands.

The Steps to Repot A Calathea

How to Repot Calathea Ornata

Here are the steps to repot a calathea according to the professional florist.

  • The first thing that you have to do is to check your calathea plant to check whether it is healthy or not. It is important for you to note that calatheas are sensitive to repotting. So, you can start with a healthy plant. If you find your plant has some brown leaves edges or yellow leaves, it is fine. However, if you see that your plant is really struggling, you have to work out why and nurse your plant back to health before you repot it.
  • You have to organize your equipment and have all the materials that you need close to your hands.
  • Let’s say that you use a plastic pot. If so, you have to squeeze the sides of the pot gently to loosen the soil from the sides of the pot. You also have to check the base of the pot. It is done to see whether any roots are growing through the drainage holes. You have to loosen these up as needed so that it is easier to remove the plant from the pot.
  • You have to turn the plant and pot on its side carefully. You have to take the plant out of the pot and make sure that you do not damage the foliage when you take it out. You can take the plant out by holding the pot upside down where you place one hand over the soil to support the plant, and you have to use your other hand to turn the pot upside down and gently pull on the pot.
  • If you find that you are struggling to take the plant from the pot, you are able to further loosen the soil. It can be done by carefully entering a knife down the inside of the pot and then gently running this around the inside of the pot.
  • After you remove the plant from the pot, you have to inspect the visible roots that you are able to see. You have to make sure that they light brown/ white and feel rather firm and spongy. If you find that the roots are black, smelly, fragile, and soggy, it means that the roots are rotting.
  • You do not have to loosen the soil or roots.
  • Now, in a new pot, you have to add 1 to 2 inches or 2.5 to 5 cm of new potting mix to the pot. Then, you have to place the plant on top of this new soil and then you have to test the level of the plant. It is done to have the level of the soil come up to about 0.5 to 1 inches or 1.25 to 2.5 cm from the top of the pot.
  • Next, you have to hold the plant in the center of the pot and then you have to add fresh soil around the plant by using your hands or a shovel and fill the pot with soil. Then, you have to firm the soil gently around the plant. However, you have to make sure that you do not compact it too much.
  • After the plant is planted in its new pot, now you are able to add a little water. You just have to add enough water to make the soil lightly moist and it is important for you to note that the roots of your new plant may not work well for some weeks because of the shock of repotting.
  • You have to place your plant in moderate heat and lighting. If you place it in a very hot temperature or under direct sunlight, your plant can get stressed. You can increase humidity as much as possible because it can reduce the risk of foliage problems in the weeks after you repot it. You are able to use humidity levels to be above 60% for your calatheas. Read also about lighting instructions for Calathea..
  • You have to make sure that you do not fertilize your plant after you repot it for at least 4 to 6 weeks. If you fertilize it after repotting it, it can cause root damage and it can make your plant more difficult for your plant to reestablish itself after repotting.
  • It is better for you not to expect any new growth for at least 4 to 6 weeks because your plant is still adjusting to its new home.

When Can We Repot Our Calathea?

As explained on the professional florist, if you want to repot your calathea, you can do it in early spring. However, you can do it anytime as long as you can provide good conditions after you repot it. After reporting, usually most calatheas take a while to adjust with a new pot. Some plants even show some signs of stress on their leaves such as brown leaf edges, or yellowing of lower leaves.

If you repot your calathea in spring, your plant is entering a fast growth phase. So, after the period of adjustment, a lot of healthy growth will be produced throughout the growing season.

Leave a Reply

Your email address will not be published. Required fields are marked *